configuration information with no manual intervention. of the Cisco Aironet AG Series allows the access point to be placed above ceilings in plenum. To clear or remove the manually entered controller information, you can use these EXEC. installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has.

Author: Moogubar Faurg
Country: Malaysia
Language: English (Spanish)
Genre: Automotive
Published (Last): 26 April 2014
Pages: 477
PDF File Size: 20.89 Mb
ePub File Size: 14.88 Mb
ISBN: 822-7-22865-528-7
Downloads: 81885
Price: Free* [*Free Regsitration Required]
Uploader: Yojin

Page 33 SSIDs to eliminate the conflict.

Cisco Aironet 1130AG Quick Start Manual

Page 48 Replacement, Repair, or Refund Policy for Hardware Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten 10 working days after ciscl of a Return Materials Authorization RMA request. Set the power settings and power injector fields and verify your switch status as indicated in the power settings table. Notes contain helpful suggestions or references to materials not contained in Note this manual.

Package Contents Each access point package contains the following items: If you are using a non-Cisco switch, changes to the power settings are not required.

Figure shows an access point in an all-wireless network. The Express Setup page appears.

Configure the settings using the following sections as a guide. Cisco does not sell Ethernet cable rated for use in a building environmental air space, such as above Caution suspended ceilings.

The security hasp covers the cable bay area including the power port, Ethernet port, console Note port, and the mode button to prevent the installation or removal of the cables or the activation of the mode button. IP address and shared secret for an authentication server on your network server authentication port Page 72 Saves changes made on the page and remains on the page. To use this guide, you should have experience working with Cisco IOS software and be familiar with the concepts and terminology of wireless local area networks.


You can determine whether your equipment is causing interference by turning it off. Configuring Power Using The Cli Intelligent Power Management support is dependent on the version of software resident in the Cisco switch that is providing power to the access point.

These documents are also available on Cisco. If you changed the IP address, you lose your connection to the access Step 7 point. Push down on the padlock to ensure the padlock is held by the security hasp adapter clips.

Your 11330ag point configuration is not changed when using the browser to reload the image file. Step 3 Enter the access point password in the Password field and press Enter.

Assigning Basic Settings When using the access point browser interface, you should disable your browser pop-up blocker. Page 69 The access point web-browser interface is fully compatible with Microsoft Internet Explorer version 6. VLAN A VLAN is a switched network that is logically segmented by functions, project teams, or applications rather than on a physical or geographical basis. Repeater 1130av Access point connects to a remote LAN, accepts root associations from wireless clients, and must associate with a root access point using the kanual interface.


If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. At the username and password prompts, enter your administrator username and password. Default Gateway The default gateway identifies the address the access point uses to access another network. Page 24 The use of a tamper-resistant head screw does not restrict access to the access point cables Note or the mode button.

Page 22 AC power adapter No configuration requirement 1. The appendix contains the following sections: Follow these steps to access them: The default enable password is also Cisco.


If required, configure the power settings as described in the previous section. Replacement, Repair, or Refund Policy for Hardware Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten 10 working days after receipt of a Return Materials Authorization RMA request.

If you press Esc Y more than ten times, you cycle to the first buffer entry. Don’t have an account? The Documentation DVD is updated regularly and may be more current than printed documentation. If there is sufficient power manuaal the radios 1130at turned on; otherwise, the access point remains in low power mode with the radios disabled to prevent a possible over-current condition.

Troubleshooting Low Power Condition On power up, the access point is placed into low power mode both radios are disabledCisco IOS software loads and runs, and power negotiation determines if sufficient power is available.

Cisco Aironet 1130AG Hardware Installation Manual

Each Cisco switch should be upgraded to support Intelligent Power Management. Remove the opening instruction label from the top cover. Launch your browser, and go to this URL: The Cisco warranty page appears.

Wireless-n access point with power over ethernet 92 pages. However, you can use the MODE button when the access point has a corrupt firmware image. Express Security Limitations Because the Express Security page is designed for simple configuration of basic security, the options available are a subset of the access point security capabilities. A username and password screen ciscco. Step 4 The access point Summary Status page appears. Enter text from picture: Page of Go.