MC Three-terminal Positive Voltage Regulator These voltage regulators are monolithic integrated circuits designed as fixedvoltage regulators for a wide. MC Fairchild datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components. Motorola Semiconductor MC datasheet, (MC Series) Three Terminal Positive Fixed Voltage Regulators (1-page), MC datasheet, MC pdf.

Author: Nall Yozshujinn
Country: Haiti
Language: English (Spanish)
Genre: Music
Published (Last): 15 October 2011
Pages: 281
PDF File Size: 7.85 Mb
ePub File Size: 2.83 Mb
ISBN: 669-3-87172-671-1
Downloads: 31313
Price: Free* [*Free Regsitration Required]
Uploader: Gara

There are LDOs Low Drop-Out which still can regulate the output if the input is only a few hundreds of mV higher and there are even ultra low drop-out types which only need a few tens of mV. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

MC Datasheet PDF –

Current Regulator Figure 9. Maximum Power Dissipation – The maximum total device dissipation for which the regulator will operate within specifications. Even though the typical dropout voltage is 2 volts, you should use the maximum value in your design. Maximum Ratings are stress ratings only.

Therefore it’s best to keep the input voltage just above the minimum to prevent the regulator to become overheated. Representative Schematic Diagram http: Load and line regulation are specified at constant junction temperature. A is a linear regulator, and does not step up the input voltage if the input is below the output for that you need a DC-DC boost regulator.


The datasheet does say how much it needs, but you may have to look for it. Email Required, but never shown. Therefore, a four-ampere plastic power transistor is specified.

MC7812 Datasheet PDF

All parameters are specified under certain conditions, and for the output voltage we can see that the condition is that the input voltage is minimum Output Noise Voltage – The rms ac voltage at the output, with constant load and no input ripple, measured over a specified frequency range.

Resistor R in conjunction with the VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof. Pulse testing datssheet low duty cycle is used. How does it go from a Maximum dropout voltage to a minimum input voltage?

Output Transistor Safe-Area Compensation?

Datasheet – MC – Voltage Regulators – Motorola

The maximum dropout voltage Vd is 2. A note on dissipation: Since the output is 12 volts, you add the two together to get a minimum input of I’ve seen LDOs with a dropout voltage of 50 mV. But since there’s this voltage drop the input voltage has to be higher than the output voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected.

  6ES7 312-1AD10-0AB0 PDF

The circuit of Figure 10 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor. Long Term Stability – Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices’ electrical characteristics and maximum power dissipation.

Dean 4, 22 57 Internal Short Circuit Current Limiting?

Datasheets search archive of electronic components datasheets

In many low current applications, compensation capacitors are not required. Linear regulators are different. Internal Thermal Overload Protection? With adequate heatsinking they can deliver output currents in excess of 1.

SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. A control element will vary the resistance in m7812 a transistor so that the output voltage will remain constant regardless of input voltage and load.

Resistor R determines the current as follows: The current to your load flows through the regulator and is the same current as will be drawn from the input voltage.