Description: The NTE is a quad 2-input positive NAND Schmitt trigger in a Lead plastic DIP type package. Each circuit functions as a 2-input NAND. Datasheet, PDF, Data sheet, manual, pdf, IC TTL/H/L SERIES, QUAD 2-INPUT NAND GATE, PDIP14, Gate, unknown. SNN datasheet, SNN circuit, SNN data sheet: TI site for Electronic Components and Semiconductors, integrated circuits, diodes, triacs.

Author: JoJohn Nikojinn
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Science
Published (Last): 7 February 2004
Pages: 188
PDF File Size: 9.92 Mb
ePub File Size: 4.81 Mb
ISBN: 194-5-14440-447-3
Downloads: 52502
Price: Free* [*Free Regsitration Required]
Uploader: Zolonris

Articles needing additional references from March All articles needing additional references All articles with unsourced statements Articles with unsourced statements from June Commons category link is on Wikidata Wikipedia articles with GND identifiers. If our sketch includes a 4-input AND gate, you might think we would simply grab a off the shelf and wire it up.

Neglecting V BEthe high threshold value is approximately. Again, there is a positive feedback but now it is concentrated only in the satasheet cell. In this circuit, the two resistors R 1 and R 2 form a parallel voltage summer.

TTL Logic IC 74132, DIP-14

Some operational amplifiers are designed to be used only in negative-feedback configurations that enforce a negligible difference between the inverting and non-inverting inputs. Now, the two resistors R C1 and R E form a voltage divider that determines the low threshold.

The input voltage must rise above the top of the band, and then below the bottom of the band, for the output to switch off minus and then back on plus. In this arrangement, attenuation and summation are separated: The base resistor R B can be omitted as well so that the input voltage source drives directly Q1’s base.

Digital Circuits/7400 Series

The Schmitt trigger was invented by American scientist Otto H. That filtered output passes to the input of a Schmitt trigger. To simplify the circuit, the R 1 —R 2 voltage divider can be omitted connecting Q1 collector directly to Q2 base.


By adding a bias voltage in series with resistor R1 drop across it can be varied, which can change threshold voltages. This may require additional shifting circuit following the trigger circuit. In the inverting amplifier voltage drop across resistor R1 decides the reference voltages i. So, it can be converted to a Schmitt trigger by connecting an additional base resistor R to one of the inputs Q1 base in the figure.

NTE – IC-TTL Quad 2-Input NAND Schmitt Trigger

The output voltage always has the same sign as the op-amp input voltage but it does not always have the dataseet sign as the circuit input voltage the signs of the two input datashwet can differ.

For example, an amplified infrared photodiode may generate an electric signal that switches frequently between its absolute lowest value and its absolute highest value. The net effect is that the output datsaheet the Schmitt trigger only passes from low to high after a received infrared signal excites the photodiode for longer than some known period, and once the Schmitt trigger is high, it only moves low after the infrared signal ceases to excite the photodiode for longer than a similar known period.

The symbol for Schmitt triggers in circuit diagrams is a triangle with a symbol inside representing its ideal hysteresis curve.

The input voltage is applied to the inverting input; datasheer output voltage of the voltage divider is applied to the non-inverting input thus determining its threshold. For the NPN transistors shown on the right, imagine the input voltage is below the shared emitter voltage high threshold for concreteness so that Q1 base-emitter junction is reverse-biased and Q1 does not conduct. When the circuit input voltage is between the thresholds, the output voltage is undefined and it depends on the last state the circuit behaves as an elementary latch.


Consequently, inverting configurations within an integrated circuit may be naturally inverting, while non-inverting configurations are implemented with a single inverter, and stand-alone inverting configurations may be implemented with two inverters.

ic datasheet & applicatoin notes – Datasheet Archive

Additionally, slow negative feedback is added with an integrating RC network. In the inverting version, the attenuation and summation are separated. Dstasheet has related information at logic family. The trigger is toggled high when the input voltage crosses down to up the high threshold and low when the input voltage crosses up to down the low threshold.

This is called the “odd but not even gate” meaning that an icc number of inputs need to be high in order for the output to be high. In other projects Wikimedia Commons Wikipedia.

Wikipedia has related information at series. The current begins steering from the right leg of the circuit to the left one.

datsheet The emitter-coupled version has the advantage that the input transistor is reverse biased when the input voltage is quite below the high threshold so the transistor is surely cut-off. The first two of them are dual versions series and parallel of the general positive feedback system.